MFM-Papago Map 101104 Feedback

[76gpsguy]

Please post your comments and feedback strictly for MFM-Papago Map 101104 only.

All posts must state the Papago version which you are using currently as per below format or it will not be entertained and responded.

PPG version : [M3GPS / Eastgear / iPhone / Android / WM Retail / WM HTC ] – [X2 / X3SE / M6 / M7 / ….]

e.g.
PPG version : M3GPS – X3SE
Feedback : ……….

Please note that MFM-Papago map only support the above said Papago versions, any feedback in relation to Papago other than the above versions will not be entertained and responded.

[batoo]

Hi,

Thanks for the great work,

just installed the map on my WM phone PPG (standard map)

I just noticed that POI in the map version got problem! if you try to tap on POI SEARCH then KEY WORDS, try to search any poi, it fails! in contrast with the previous map version (april 2010), where you can seek any POI smoothly.

TQ

[leoyew]

Finally ! 我等到花儿也谢了！hehe, but i wish that the papago map can support latest papago M7 software, if it could be done i can said Malfreemap is the best !

[azlan96]

Finally ! 我等到花儿也谢了！hehe, but i wish that the papago map can support latest papago M7 software, if it could be done i can said Malfreemap is the best !

it does

Supported Devices/Softwares
* M3GPS Papago X3, X5~X7
* Eastgear Papago X3
* Papago X5 for Android
* Papago M6~M7 for iPhone

[zamad]

Hi,

Thanks for the great work,

just installed the map on my WM phone PPG (standard map)

I just noticed that POI in the map version got problem! if you try to tap on POI SEARCH then KEY WORDS, try to search any poi, it fails! in contrast with the previous map version (april 2010), where you can seek any POI smoothly.

TQ

That is strange... I just did a drive around Shah Alam after selecting POIs and I did not experience what you did. Works fine on my PND.

PPG Version: M3GPS - X5SE
PPG Unit: R5800

[shawchyn]

Hi,

Thanks for the great work,

just installed the map on my WM phone PPG (standard map)

I just noticed that POI in the map version got problem! if you try to tap on POI SEARCH then KEY WORDS, try to search any poi, it fails! in contrast with the previous map version (april 2010), where you can seek any POI smoothly.

TQ

That is strange... I just did a drive around Shah Alam after selecting POIs and I did not experience what you did. Works fine on my PND.

PPG Version: M3GPS - X5SE
PPG Unit: R5800

He is refer to the "standard" map for Windows Mobile Version of Papago X5. This is an "known" issue. Patches will be reloaded in few days time.

[pasculy]

My patience paid off. Downloaded this morning & had tried driving around Penang, only few POI showed error when it was selected. The rest, satellite locking was quite decent, at first it took 5 minutes. After driving around, shutting it down & turn it on, satellite locking stabilized, around 45 second to 1 minute.

BTW, I'm using R5800 with latest routing fix & X5SE. Thanks to the team & contributor.

[nelsonlee]

Tested and the feedback is very lagge even for simulation.....
Maybe you need to workout the Standard.mb6 file to make it run smooth!!

Regards,
Nelson

[mission8]

I just discovered that it doesn't display junction view with this new map.
Can someone pls advise?

[nelsonlee]

I just discovered that it doesn't display junction view with this new map.
Can someone pls advise?

Tested and have junction view.....you may need to check on your advance setting.....
The new maps still need to improve for Standard.m6 file, because it still lagge!!

Regards,
Nelson