MFM-Papago Map 101104 Feedback

[shin0327]

Help me!!i ard install PPG map in my Holux device.y i cant find the file in the Switch Maps?
What happen?Urgent!!!
Help me Plz...!!

[ccwong]

Help me!!i ard install PPG map in my Holux device.y i cant find the file in the Switch Maps?
What happen?Urgent!!!
Help me Plz...!!

Makesure you select "Eastgear Papago X3" during map installation...

[sHawTY]

Whoops, sorry.
Didn't know the fix has already been uploaded.

[9w2vvh]

PND = M3GPS X5
Download ok, run no problem.

Tnx vry much to PPG Map Team for hard wrking. 73

de 9w2vvh, sungai besar

[zeevon]

Please check to routing from southern part of penisular malaysia to northern part of penisular malaysia. Instead of direct you to exit Nilai utara into Elite express at NS express, it will direct you to enter k.l.

i.e from Batu pahat to ipoh. The routing will enter Sungai besi toll -> K.L seremban express--> federal highway -->east west link --> exit P.J --> Federal Highway Klang-->kerinchi link --> exit mont kiara --> exit Nkve/duke --> nkve--> exit to Ipoh/Penang --> N.S express.

Wah! why so complicated!!!

I've tested on MFM 100415 and the correct routing should be Exit 214 Nilai Utara/KLIA --> Elite --> exit NKVE --> NKVE--> Exit 10B to Ipoh/Penang--> NS express.

Thanks a lot for your hard work.
I will try my best to feedback errors to you.

[zeevon]

yup. i facing the same lagging issue as yours'. navigation position slow in about 3s. means cursor position only move to the location after i pass that position in 3 sec ago. quite obvious when u already passed the juction and yet cursor still at the back.

other than that is all fine except minor errors.

issue two - routing option 1,2,3 is not fuctioning.

issue three - cant route from sabah to sarawak.

issue four - sound instruction should make it more distinctive. e.g. "at the junction pls turn right and at the junction please turn right and at the junction please turn right " in which the 2nd phrase infact its mean for the the 2nd right turn 3rd for 3rd right turn. quite confusing when in shoplot area with a few short distance of turn.

Nevertheless.. good jobs to those sifu in make this running and keep it up. this is only my comments and complaint...

These problem can be encounter if you navigate in 2D mode. The position will exactly the same as you pass by a junction. These is not the map problem. In my opinion, the papago is developed to use in standard Wince hardware, it is not possible to fully utilize the PND hardware. If they do so, the papago will only run on specific wince PND. When you switch to 3D mode, it is not using the PND 3D processor, it will lagged when you pass by a junction by about 1-3 sec depend on how fast your PND is.
Garmin is different, the firmware is fully utilize for the hardware because Garmin is manufactured the PND by itself and it is not selling the Garmin software for its own PND.
If you install Garmin Mobile XT into a Wince PND, the same problem occur.

[chindian]

Used the map when traveling from Kampar to Sg. Petani. Encountered the following. 1 or 2 POI missing. Have to recheck. NSE has been drawn over the local roads at certain stretch. See attached file. 1 or 2 JV's not visible especially at Perai and Sg. Petani South Toll Exit. No problem with routing. Lagging is acceptable compared to the Beta version. to all who contributed for the release of the map.

[pops]

can someone tell how to install the downloaded maps into my android device? thanks.

[sephiroth_hr]

can someone tell how to install the downloaded maps into my android device? thanks.

Hi, simply download custom map and install your map into your android phone Root\NaviSEA\Maps\

[mysattv]

yup. i facing the same lagging issue as yours'. navigation position slow in about 3s. means cursor position only move to the location after i pass that position in 3 sec ago. quite obvious when u already passed the juction and yet cursor still at the back.

other than that is all fine except minor errors.

issue two - routing option 1,2,3 is not fuctioning.

issue three - cant route from sabah to sarawak.

issue four - sound instruction should make it more distinctive. e.g. "at the junction pls turn right and at the junction please turn right and at the junction please turn right " in which the 2nd phrase infact its mean for the the 2nd right turn 3rd for 3rd right turn. quite confusing when in shoplot area with a few short distance of turn.

Nevertheless.. good jobs to those sifu in make this running and keep it up. this is only my comments and complaint...

These problem can be encounter if you navigate in 2D mode. The position will exactly the same as you pass by a junction. These is not the map problem. In my opinion, the papago is developed to use in standard Wince hardware, it is not possible to fully utilize the PND hardware. If they do so, the papago will only run on specific wince PND. When you switch to 3D mode, it is not using the PND 3D processor, it will lagged when you pass by a junction by about 1-3 sec depend on how fast your PND is.
Garmin is different, the firmware is fully utilize for the hardware because Garmin is manufactured the PND by itself and it is not selling the Garmin software for its own PND.
If you install Garmin Mobile XT into a Wince PND, the same problem occur.

Posted: Mon Nov 15, 2010 12:09 pm



zeevon
Post subject: Re: MFM-Papago Map 101104 Feedback

Ok. tks zeevon for clearing my doubt. will test it under 2d tomorrow and revert.

However, some error need to be rectified.

1. the Road direction inside the Times Squares Kota Kinabalu Has bn changes to clock vise instead of anti-clockwise.


rgds